Best Garden Trellis for Climbing Roses: Ten Trellises and What Their Listings State
As an Amazon Associate we earn from qualifying purchases. Details
If you are searching for the best garden trellis for climbing roses, start with the one job that matters more than its look: the frame has to hold long canes that cannot hold themselves up. Climbing roses do not cling the way some vines do, so the frame must be tall enough for the canes, strong enough to carry them, and shaped so you can guide the canes sideways or over the top. This guide compares ten metal trellises, obelisks and arches from our research set, each listed as suited to roses or climbing plants. It sets out what each listing states about height, width, material, assembly and load, and it flags where a title and its bullets disagree.
Quick answer
- Climbing roses need a structure and cannot cling to one. Iowa State University Extension says their canes require support, and an Ask Extension expert answer says the canes must be secured to it.
- Nine of the ten listings state a height, from 45 inches to 94 inches. A 70-inch frame covers about 30 percent of a 20-foot cane, so plan to train canes sideways or over the top.
- Choose the shape by the job. The obelisks suit a pot or a single bed, the arches suit a path or entrance, and the flat panels suit a fence or wall line.
- No listing in this set gives a load in pounds. Ask the seller for a load figure before you train a mature rose onto a light frame.
What climbing roses need from a trellis
Iowa State University Extension describes climbing roses as vigorous roses that produce long canes that require support. It also says they do not climb the way vining plants do, because they have no tendrils or twining habit. Like other vining plants, they need a trellis or some other structure. That is the starting point for every listing in this set.
The same Iowa State page says canes of climbing roses can reach 5 to more than 20 feet long. That range is the number to keep in mind when you read a listing. A trellis is a fixed frame, and the canes keep growing for years. A frame that looks tall on a product page can still be short for the rose it is meant to hold.
An Ask Extension expert answer puts the mechanical point plainly: climbing roses do not grab or cling to a trellis, and their long canes must be secured somehow to the support. A trellis therefore has two jobs. It has to stand up to the weight of the canes and the wind on them, and it has to give you places to fasten each cane. How many fastening points a frame gives depends on its grid or its ring spacing, and the listings in this set do not count them.
Iowa State also notes that most climbing roses bloom profusely in late spring and then bloom sporadically for the rest of the season. Plan the frame so the canes that carry the spring flush are within reach for tying and for cutting.
Heights against cane length
Nine listings state a height. Table 1 converts each stated figure to centimeters and compares it with two cane lengths: 60 inches, the 5-foot low end from Iowa State, and 240 inches, the 20-foot high end. The arithmetic is simple. Height in inches times 2.54 gives centimeters. Height in inches divided by 60 gives the number of times a 5-foot cane the frame reaches. Height in inches divided by 240, times 100, gives the percentage of a 20-foot cane the frame covers.
Table 1: stated height compared with rose cane length
| No. | Listing and shape | Stated height | In centimeters | Times a 5-foot cane (60 in) | Share of a 20-foot cane (240 in) |
|---|---|---|---|---|---|
| 1 | BAG WIZARD obelisk | 70.87 in | 180.0 cm | 1.18 | 29.5% |
| 2 | TCBWFY obelisk | 6 ft (72 in, from bullets) | 182.9 cm | 1.20 | 30.0% |
| 3 | Trellume obelisk | 37, 53 or 69 in (top setting 69 in) | 94.0, 134.6 or 175.3 cm | 1.15 at top setting | 28.8% at top setting |
| 4 | LeJoy Garden arch | Not stated | Not stated | Not stated | Not stated |
| 5 | LZRS panels | 71 in (title) | 180.3 cm | 1.18 | 29.6% |
| 6 | rubfac arch | 94 in (bullets) | 238.8 cm | 1.57 | 39.2% |
| 7 | ArdeFentium wall trellis | 60 in (bullets) | 152.4 cm | 1.00 | 25.0% |
| 8 | ArdeFentium 70.8 in panels | 70.8 in | 179.8 cm | 1.18 | 29.5% |
| 9 | hogardeck grid | 45 in (bullets) | 114.3 cm | 0.75 | 18.8% |
| 10 | ArdeFentium 47 in panels | 23.8 to 71 in when combined | 60.5 to 180.3 cm | 0.40 to 1.18 | 9.9% to 29.6% |
Reading the table, the 72-inch obelisk from the bullets is 1.20 times the 60-inch low end and covers 30.0 percent of the 240-inch high end. The 94-inch arch is the tallest stated frame, and it covers 39.2 percent of a 20-foot cane. The 45-inch grid trellis is the shortest, and it covers 18.8 percent. Even the tallest frame in the set reaches less than half of the longest canes Iowa State describes. For a mature climber, the frame is a starting support, not a full solution.
Three notes qualify the table. The title of the 6 FT obelisk gives 70 inches, but its bullets say 6 FT. Six feet is 72 inches, so the table uses the bullets and the gap is 2 inches. The Trellume obelisk lists three settings, and the table shows the top one. The LeJoy Garden arch states no height in its title or bullets, so it cannot go in the table.
A frame shorter than the cane is not wrong. It can still hold the lower part of the cane, and the upper canes can be guided sideways or over the top, as the next sections explain.
Obelisk, arch or flat panel
The ten listings fall into three shapes.
Obelisks are narrow, tapering frames that stand on the ground, usually with stakes or a base. Three listings are obelisks. Their stated heights run from 37 to 72 inches, and the Trellume listing says its frame suits pots, raised beds and garden areas. An obelisk fits a single plant in a pot or a bed, and it lets the canes fan out around a central point. The Ask Extension expert described a different kind of frame, a square-top arbor, but the same difficulty applies where any frame has a top and the canes must change direction. Thick rose stems resist sharp turns.
Arches are open frames with a top you can walk under. Two listings describe themselves as arches in their bullets: the LeJoy Garden galvanized arbor and the rubfac 7.8-foot arch. The rubfac bullets lead with event, wedding and balloon use, so that arch reads as decor first. The LeJoy listing calls its frame a garden arbor and says it doubles as a trellis for vines and roses.
Flat panels and grids are the third shape. They form a single plane that fits a fence line, a wall or the edge of a bed. Five listings fall here, including the LZRS listing, whose title says arch but whose bullets describe two panels. All five panel listings state a width, so you can measure the space before you choose. The ArdeFentium listings say their panels can be combined, folded or used on their own, which makes them the most flexible shape in the set.
No source we opened compares these three shapes, so the choice rests on the space and the job. A panel suits a boundary where the rose runs along a line. An obelisk suits one plant in a pot or a bed. An arch suits a path where you want the rose overhead. Each shape has the same underlying limit: the frame stops, and the cane keeps growing.
Training canes onto the frame
The Ask Extension answer on a square-top arbor gives the most specific advice in the pages we opened. The expert said thick rose stems often do not bend into right-angle turns. The options were to snip the tips of the tallest stems near the arbor corners so they form side branches that are easier to train and tie, or to let the uppermost canes grow taller so they arch over the top on their own.
Those two options fit a frame that is shorter than the cane. The timing detail matters. The expert said to snip after peak bloom, in case cutting too early reduces flowering. That is the only timing the pages we opened give for this step.
The pages we opened do not give a tie spacing, a tie material or a method for fastening a cane to a panel. Check the seller’s instructions and your regional extension office before you tie a mature rose, and follow the material the extension office recommends for ties.
If you plan to set the trellis in a planter, our deck planter box guide covers planter boxes built for a deck railing, which is a different job from a ground-set trellis. If the trellis stands in a raised bed, our guide to vegetables for raised beds lists what else goes in the bed.
What each listing states
Each paragraph below paraphrases one listing. It says what the listing states, and it marks what the listing leaves out.
Obelisks
The 2 Pack 70.87-inch obelisk from BAG WIZARD states a height of 70.87 inches and adjustable tiers that let you change the height as the plant grows. Its bullets name roses, clematis and tomatoes as plants it supports. The frame is described as PVC-coated metal that resists rust, fading and weather damage, and the assembly is described as tool-free, with the frame detaching for off-season storage. The title says 2 Pack, but the bullets describe one trellis and give no count, so confirm the pack size before you order. No width or base size is stated anywhere in the title or bullets.
The 6FT obelisk from TCBWFY states six feet, which is 72 inches in the bullets, although its title says 70 inches. Its bullets describe metal tubes with bumps that guide stems upward, four adjustable rings and four stakes that anchor the frame in the ground. The bullets say assembly needs no screws, wrenches or screwdrivers. The title calls the frame rustproof and describes a thickened tube, but the bullets do not repeat those words. No width or load is stated.
The 69-inch obelisk from Trellume offers three height settings, 37, 53 and 69 inches, and each step adds a support ring. Its bullets describe steel pipe with a thick plastic coating, which the listing says resists rust and protects stems from hot and cold temperatures. The bullets name roses, clematis, jasmine and vegetable vines, and they say the frame is tool-free and detachable. The title gives only the 69-inch top setting. The listing gives neither a width nor a load.
Arches
The galvanized arch from LeJoy Garden states neither a height nor a width in its title or bullets. Its bullets describe a galvanized steel frame that the listing says was made thicker, from 0.3 mm to 0.4 mm, and heavier, from 4 lb to 5.54 lb. The 5.54 lb figure is 1.54 lb more, or about 38.5 percent heavier than the earlier 4 lb figure in the same bullets. The bullets say one person can assemble it, with pre-drilled holes, and that a screwdriver is included. They name roses and morning glories as plants it supports, and they describe it as an event backdrop as well. The bullets also make a replacement guarantee claim, which is the seller’s statement. No load is stated.
The 7.8-foot arch from rubfac states, in its bullets, about 55 inches wide and 94 inches high. The title describes a metal trellis for climbing plants, but the bullets lead with event, wedding and balloon use, and they say the arch is not only a garden trellis. Roses are not named in the title or the bullets, only climbing plants. The bullets describe assembly and disassembly as easy and say the arch suits indoor and outdoor use. No load is stated. This is the tallest frame in the set and the only one above 90 inches.
Flat panels and grids
The 60-inch wall trellis from ArdeFentium states 60 inches tall and 33.3 inches wide in its title and bullets. The bullets describe an 8 mm metal tube frame with 4 mm solid mesh, screw-fixed joints and all hardware included. The panels can be set straight, curved, folded or used as separate panels, and roses are named in the title and bullets. The bullets describe outstanding load-bearing capacity, but they give no pound figure. The mesh opening size is not stated.
The 2 Pack 70.8 by 19.7-inch trellis from ArdeFentium states those dimensions in both the title and bullets. It has a 13 mm outer frame and 3 mm inner mesh, which the bullets say gives stems and tendrils more contact points than wider grids. The panels assemble in two parts, and the bullets name roses, clematis and vegetables. The bullets refer to decorative arch styling, although the frame is a slim vertical panel. No load is stated, and the only width given is 19.7 inches.
The 45-inch grid trellis from hogardeck gives 45 inches in the bullets, and its title adds a 14-inch width. The bullets describe rust-resistant iron with a black powder finish and 10-inch ground stakes. The frame splits into two lightweight sections for storage. The bullets name climbing roses, tomatoes, cucumbers and wisteria. The first bullet has a blank where an engraved phrase should be, so the listing’s design detail is incomplete. At 45 inches it is the shortest stated height in the set.
The LZRS listing’s title describes a 71 by 20 inch arch. The bullets describe a set of two panels that install side by side, with screws joining the top and bottom pieces to the ground or a planter. A hook design is said to allow adjustable angles, and the coating is black powder-coated iron. The bullets name roses, ivy, clematis and vegetables. The 71 by 20 inch figure comes from the title only, and no load is stated.
The 2 Pack 47-inch trellis from ArdeFentium is described in its title as an arched rose trellis, 17 inches wide. The bullets describe two 47 by 17 inch panels that can be used alone or combined for adjustable heights from 23.8 to 71 inches, with a 10 mm metal tube frame and 11.8-inch ground stakes. The bullets say assembly is tool-free with included screws and that the coating resists rust, fading and peeling. The bullets describe modular panels and do not describe an arch, so the arched word appears only in the title. No load is stated.
Stated materials, widths and assembly
Table 2 records what each listing states about width, material, assembly and load. “Not stated” means the title and bullets say nothing about that feature.
Table 2: features stated in each listing
| No. | Listing | Width stated | Material per listing | Assembly per listing | Load in pounds stated |
|---|---|---|---|---|---|
| 1 | BAG WIZARD obelisk | Not stated | PVC-coated metal | Tool-free, detachable | No |
| 2 | TCBWFY obelisk | Not stated | Metal tubes with bumps | No screws or tools, four ground stakes | No |
| 3 | Trellume obelisk | Not stated | Steel pipe with plastic coating | Tool-free, detachable | No |
| 4 | LeJoy Garden arch | Not stated | Galvanized steel, 0.4 mm | One person, pre-drilled, screwdriver included | No; weight 5.54 lb |
| 5 | LZRS panels | 20 in (title) | Iron, black powder coat | Screws at top and bottom | No |
| 6 | rubfac arch | About 55 in (bullets) | Metal | Easy assembly and disassembly | No |
| 7 | ArdeFentium wall trellis | 33.3 in (bullets) | 8 mm tube frame, 4 mm mesh | Screw-fixed, hardware included | No pound figure |
| 8 | ArdeFentium 70.8 in panels | 19.7 in (title and bullets) | 13 mm outer frame, 3 mm mesh | Two-part assembly | No |
| 9 | hogardeck grid | 14 in (title only) | Rust-resistant iron, black powder finish | Two sections, no tools | No |
| 10 | ArdeFentium 47 in panels | 17 in per panel | 10 mm tube frame | Tool-free with included screws | No |
Two figures stand out. Only the LeJoy Garden arch gives a weight, and that weight is up from 4 lb to 5.54 lb in the same bullets. Only the ArdeFentium wall trellis uses the phrase load-bearing capacity, and it gives no number. Every obelisk listing leaves its width out, so the obelisks need a measurement of the pot or bed before you order.
Where titles and bullets disagree
Where a title and its bullets give different facts, this article uses the bullets, and the difference is listed below.
- 6FT obelisk, TCBWFY: the title gives 70 inches, and the bullets give 6 FT, or 72 inches. The table uses the bullets.
- Panel set, LZRS: the title says arch, and the bullets describe two panels set side by side. The table takes its 71-inch height from the title, because the bullets give no height.
- Panel set, ArdeFentium 47 inch: the title says arched, and the bullets describe two modular panels with no arch. We used the bullets for that row.
- Obelisk, BAG WIZARD: the title says 2 Pack, and the bullets describe one trellis without a count. The pack size is unconfirmed.
- Obelisk, Trellume: the title gives only the 69-inch top setting, and the bullets give three settings, 37, 53 and 69 inches. The table uses the top setting and notes the others.
- Arch, rubfac: the title says trellis for climbing plants, and the bullets lead with event decor. This is a difference in emphasis rather than a conflict.
- Grid trellis, hogardeck: the first bullet has a blank where an engraved phrase should be. Do not rely on that bullet for a design detail.
How we chose
We started from the search results for garden trellis for climbing roses on Amazon and read each product page in Chrome on 2026-10-20. We kept the listings whose title or bullets describe a garden trellis, obelisk or arch for climbing roses or climbing plants. We left out raised beds, plant stands, a Halloween archway described as decor, and the sponsored results. The first page held 46 non-sponsored listings of the right type, which was more than eight, so we did not load a second page. Where two listings described the same frame, we kept one.
From those 46, we chose ten that cover three shapes and span stated heights from 45 inches to 94 inches. We did not rank them. The listings do not supply the data a ranking would need, and the pages we opened do not establish which frame holds a rose best. We did not use price, ratings or sales data, and this article does not store or use them.
What we could not verify
- Load. None of the ten listings gives a figure in pounds. The wall trellis uses the phrase load-bearing capacity, but it gives no number. The pages we opened do not give a safe load for a climbing rose.
- Coatings. Several listings say their frames are rustproof, rust-resistant or weather-resistant. The pages we opened do not cover the coatings of garden trellises, so those are the sellers’ statements.
- Ground anchoring. Two listings give stake lengths, 10 inches and 11.8 inches. The other listings give no stake length, and the pages we opened do not say how deep a stake should go.
- Wall distance. No listing gives a distance from a wall, and the pages we opened do not give one.
- Tie method. The pages we opened do not give a tie spacing or a tie material for climbing rose canes.
- Mesh openings. The grids and panels list tube and mesh thicknesses but not the size of the openings, so we cannot compare how far a cane can reach through them.
- Obelisk widths. None of the three obelisk listings states a width or a base size.
- Long-term performance. The pages we opened do not say how any frame holds up after years of rose growth. That depends on the rose, the site and the weather.
1. 2 Pack 70.87″ Garden Obelisk Trellis for Climbing Plants, Pyramid Design for Roses, Clematis (BAG WIZARD 2 Pack 70.87 inch pyramid obelisk trellis)
Pros
- The bullets state a height of 70.87 inches with adjustable tiers
- The bullets name roses and clematis as plants it supports
- The bullets describe a PVC-coated metal frame and tool-free, detachable assembly
Cons
- The title says 2 Pack, but the bullets do not give a count
- No width or base size is stated in the title or bullets
Best for: A tall obelisk for one plant in a pot or a small bed, where a 70-inch frame gives a rose a central support
Skip if: You need a stated width or base size before you buy
View on Amazon (affiliate link)
2. 6FT Garden Obelisk Trellis for Climbing Plants,70”Metal Plant Support Tower, Heavy Duty Thickened (TCBWFY 6 foot metal obelisk trellis with four ground stakes)
Pros
- The bullets state 6 FT, which is 72 inches, the tallest stated height among the obelisks
- Four ground stakes that the bullets say anchor the frame
- Four adjustable rings and no screws or tools needed, according to the bullets
Cons
- The title says 70 inches while the bullets say 6 FT, a gap of 2 inches
- The bullets state no width and no load
Best for: The tallest obelisk in the set, for a rose that will climb a tall frame set in the ground
Skip if: You need the title and bullets to give the same height, or a stated width
View on Amazon (affiliate link)
3. Garden Obelisk Trellis for Climbing Plants Outdoor 69″ H (1 Pack) (Trellume 69 inch obelisk trellis with three height settings)
Pros
- Three stated height settings of 37, 53 and 69 inches, with each step adding a support ring
- Steel pipe with a thick plastic coating, which the bullets say resists rust
- The bullets name roses and clematis and say the frame is tool-free and detachable
Cons
- The title gives only the 69 inch top setting
- The bullets give no width or load figure
Best for: A frame you can set at 37, 53 or 69 inches as the rose grows
Skip if: You need a single fixed height or a stated width
View on Amazon (affiliate link)
4. Garden Arch Galvanized Metal Rust-Proof Heavy Duty for Climbing Vines Roses (LeJoy Garden galvanized metal garden arch for vines and roses)
Pros
- The bullets say the frame is thicker than before, 0.4 mm instead of 0.3 mm, and weighs 5.54 lb
- The bullets say one person can assemble it with pre-drilled holes and a screwdriver included
- The bullets name roses and morning glories as plants it supports
Cons
- Neither the title nor the bullets state a height or a width
- The bullets give a weight but no load figure
Best for: An arch over a gate or path that a rose can climb, for a buyer who wants one person to assemble it
Skip if: You need a stated height or width before you buy
View on Amazon (affiliate link)
5. 2 Pack 71x20in Rustic Iron Arch Decoration Garden Trellis with Black Metal Coating – Perfect (LZRS 71 by 20 inch iron trellis, two-panel set)
Pros
- Two panels that the bullets say install side by side for added stability
- Black powder-coated iron, according to the bullets
- The bullets name roses, ivy, clematis and vegetables
Cons
- The title says arch, but the bullets describe two panels
- The 71 by 20 inch size comes from the title only
Best for: A pair of iron panels set side by side for a fence line or the edge of a planter
Skip if: You need a single arch or a size that the bullets confirm
View on Amazon (affiliate link)
6. RUBFAC 7.8ft Garden Arch, Metal Trellis for Climbing Plants Outdoor (RUBFAC 7.8 foot metal garden arch for an entrance)
Pros
- The bullets state about 55 inches wide and 94 inches high
- Easy assembly and disassembly, according to the bullets
- The bullets say it suits indoor and outdoor use
Cons
- Roses are not named in the title or the bullets, only climbing plants
- The bullets stress event and balloon use, so it reads as decor first
Best for: A tall arch at a garden entrance or walkway, where the 94-inch height frames a path more than a single rose
Skip if: You need a rose-specific claim or a stated load before you buy
View on Amazon (affiliate link)
7. 60'' H x 33.3'' W Metal Garden Trellis for Climbing Plants Outdoor – Rustproof Plant Support (ArdeFentium 60 inch metal wall trellis, 33.3 inches wide)
Pros
- A stated size of 60 inches tall and 33.3 inches wide
- An 8 mm tube frame and 4 mm solid mesh, according to the bullets
- Screw-fixed joints with all hardware included, and panels that can be used separately
Cons
- The bullets describe load-bearing capacity but give no pound figure
- No mesh opening size is stated
Best for: A wall or fence trellis for a rose along a boundary, with panels that can be curved or separated
Skip if: You need a pound figure or a mesh opening size before you buy
View on Amazon (affiliate link)
8. 2 Pack 70.8″ X 19.7″ Metal Garden Trellis for Climbing Plants Outdoor – Rustproof Heavy Duty Arched (ArdeFentium 70.8 by 19.7 inch metal trellis, 2 pack)
Pros
- A stated size of 70.8 by 19.7 inches in both the title and the bullets
- A 13 mm outer frame and 3 mm inner mesh, according to the bullets
- A two-part assembly that the bullets say is simpler than styles with many loose pieces
Cons
- The bullets give no load figure
- The bullets do not say how far the panels stand off a wall
Best for: A slim trellis for a rose in a bed or against a fence, with a denser mesh for young stems
Skip if: You need a stated load or a wall distance before you buy
View on Amazon (affiliate link)
9. 1PC 45×14 Inch Heavy Duty Metal Trellis – Black Rustproof Coated Outdoor Garden Support (hogardeck 45 inch black iron grid trellis with ground stakes)
Pros
- The bullets state a 45-inch height, and the title adds a 14-inch width
- Rust-resistant iron with a black powder finish and 10-inch ground stakes, according to the bullets
- Two lightweight sections that come apart for storage, according to the bullets
Cons
- The first bullet has a blank where an engraved phrase should be
- At 45 inches it is the shortest stated height in the set and may not reach a long cane
Best for: A short grid for a container or a low bed, where 45 inches is enough for a young rose
Skip if: You need a frame taller than 45 inches for a long cane
View on Amazon (affiliate link)
10. 2 Pack 47″ H x17 W Garden Trellis for Climbing Plants Outdoor – Metal Rustproof Arched Rose Trellis (ArdeFentium 2 pack 47 inch panels with adjustable height from 23.8 to 71 inches)
Pros
- The bullets say the two 47 by 17 inch panels combine for heights from 23.8 to 71 inches
- A 10 mm metal tube frame and 11.8-inch ground stakes, according to the bullets
- Powder-coated metal that the bullets say resists rust, fading and peeling
Cons
- The title says arched, but the bullets describe two modular panels
- The bullets describe the adjustable range only briefly, without the joining method
Best for: A modular trellis for a rose you want to grow taller over the season, by adding or combining panels
Skip if: You need one fixed height or an arch shape
View on Amazon (affiliate link)
FAQ
How tall should a trellis for climbing roses be?
Iowa State says climbing rose canes can reach 5 to more than 20 feet. Among the nine listings that state a height, the range runs from 45 inches to 94 inches. A 70-inch frame covers about 30 percent of a 20-foot cane, so plan to train the canes sideways or over the top, not only up the frame.
Do climbing roses need to be tied to a trellis?
Yes. An Ask Extension expert answer says climbing roses do not grab or cling to a trellis, and that their long canes must be secured to the support. The pages we opened do not give a tie spacing or a tie material.
What do I do when the canes are too thick to turn at a corner?
An Ask Extension answer about a square-top arbor says thick rose stems often do not bend into right-angle turns. The expert suggested snipping the tallest stems near the corners after peak bloom, so they form side branches, or letting the uppermost canes grow over the top. That answer is about an arbor, but the same bend problem can appear on an arch or an obelisk top.
Obelisk, arch or panel: which shape should I pick?
Let the job set the shape. The three obelisks state heights between 37 and 72 inches, and their listings suit pots and beds. The arches suit a path or entrance, and the tallest arch states 94 inches. Flat panels and grids fit a fence or wall line, and all five panel listings state a width. No source we opened compares the shapes, so measure the space and decide from the stated size.
Which listings name roses in the title?
Eight of the ten titles name roses. The two that do not are the Trellume obelisk and the rubfac arch. The Trellume bullets do name roses, but the rubfac bullets name only climbing plants, so a rubfac arch needs a check before you plant a rose at its base.
Bottom line
Pick the frame by the height your canes will reach and then by the shape your space needs. Check the stated width and height first. No listing in this set gives a load in pounds, so ask the seller for a load figure before you train a mature rose onto a light frame.
Sources
- Iowa State University Extension and Outreach, Yard and Garden, “Rose Types and Cultivars”, opened 2026-10-20: https://yardandgarden.extension.iastate.edu/how-to/rose-types-and-cultivars
- Ask Extension, “Trellising Climbing Rose” (question 815303, expert response), opened 2026-10-20: https://ask.extension.org/kb/faq.php?id=815303
- Ask Extension, “Climbing Rose Maintenance for Fall/Winter” (question 850568, expert response), opened 2026-10-20: https://ask.extension.org/kb/faq.php?id=850568